10 Quick Tips About Fiat Panda Key Fob Replacement

Reasons Your fiat key fob not working 500 Key Fob Won't Work

A fiat 500 key fob is a great way to unlock the doors and get started the car. There are a myriad of reasons why the fob won't be functioning. It could be due to a dead battery or damaged receiver module, water damage issues, or interference.

This listing is for an NEW replacement fiat 500 car key panda key (pattern-wiki.win) Fiat Flip Key Remote - like the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here for Locksmith Search). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob being inoperative. Modern key fobs have a very limited operating range and should be within some feet of the vehicle to operate. If you're far away from your vehicle, and you press the key fob button, the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin-cell battery (Part Number CR2032) by a fresh one of a reliable brand, like Panasonic Duracell or Energizer. You can find them in your local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while standing close to your fiat doblo key programming 500. The car will blink its parking lights and the key fob should operate the lock and unlock switches.

If your fob's key isn't working after replacing the battery, it may be water damage which has prevented it from connecting to the module in your vehicle. Water damage can happen in many ways, including an easy splash or submerging the key fob saltwater at the beach. If you suspect your fob has been exposed to water, you can try placing it in a dry rice bag to draw the moisture back out. If that doesn't work, your fob will probably require reprogramming by an experienced locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob in the ocean or wash it in a machine. Saltwater can cause the circuit board to short, and eventually die. It's not a good thing to let the fob get wet however, but don't give it up even if you accidentally drop the fob in water, or fail to take it out of your pants pocket.

First, remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Then try the fob and test if it works. If the key does not work, it may have to be changed. This is usually done by an auto locksmith or dealer.

If your key is a bit older and has not been programmed for your car it is necessary to replace it completely. A professional locksmith for automotive can complete this simple process. The locksmith will have to cut the key to match the ignition in your vehicle. They'll also need to program the fob into your car's system. This is a fast and inexpensive process which can be completed within the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote's range is of 30 feet, which means in the event that you are far from your car it will not respond to your commands. It's easy to fix this by moving the remote closer to your car until it responds.

If you've replaced the battery on your coin (commonly known as a "button" or "watch") and your fob still won't work It could be because of an internal circuit board problem. In the majority of cases, reprogramming your fob can resolve the problem. You can find directions on how to do this on the majority of automobiles by searching YouTube or reading the owner's manual.

You may have to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension it may prevent your battery from sitting properly and cause your remote to malfunction.

In rare instances the fob could be desync'd with your vehicle due to software problems or hardware issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances they might need to install the software again in your body control module, too.

Interference

In addition to a dead battery on a coin The key fob may not be able to receive or transmit signals due to interference. This can occur when the keyfob is in close proximity to a radio transmitter like a cellphone or radar detector. Other reasons the key fob may not function could be due to a weak connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. You might have a damaged 500 receiver module if you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all of the on-board systems in your 500 keys, including the key fob. Disconnect the battery of 12 volts for about 15 minutes, by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electricity and restart the car's computers. This can help the key fob to function again. If the problem persists you should seek out an expert technician. They will be able to identify the exact cause of any problems.